jack72 0 Posted July 19, 2009 So far everytime I Warp and the come out and I am above 10,000 feet, my plane's engine will quit. I try and hit E to restart but get a message that it fails. I then try and manual start with hiting Shift S continuosly but it will only restart 50% of the time. This engine failure always happens everytime I hit warp and ctl x to get out of the warp. Is there a way to fix this. Share this post Link to post Share on other sites
Launchbury 1 Posted July 19, 2009 Your mixture it too rich. Assign a button to decrease mixture, and keep pressing it until the engine picks back up. Share this post Link to post Share on other sites
Condor44 0 Posted July 19, 2009 Your mixture it too rich. Assign a button to decrease mixture, and keep pressing it until the engine picks back up. Better yet an axis if you have one that's not being used. Share this post Link to post Share on other sites
SirMike1983 3 Posted July 19, 2009 I assign to a joystick button and then use the "repeater" slide in the controls menu to allow me to hold down the buttons to lean and enrich as I need. At that height your mixture will be very lean-- perhaps only a couple steps above cut. Share this post Link to post Share on other sites
+Polovski 460 Posted July 19, 2009 Set mixture lower before you warp.. Share this post Link to post Share on other sites
Broadside uda Barn 0 Posted July 20, 2009 I have had this happen at least 2 times, WITH auto mixture on. I dive to get some speed, hit E to restart engine, and usually after a few attempts I'll get it going, tho sometimes I cant maintain RPMs. Then I check the map head for my lines and find a field/base to land in. Share this post Link to post Share on other sites
+Polovski 460 Posted July 21, 2009 Yep dive some, start engine, and whilst diving some lower mixture quickly to catch it, with a bit of practice you can restart whilst high. Share this post Link to post Share on other sites
zoomzoom 2 Posted July 21, 2009 Well, to answer your question more simpy......."There's no air....up there." ZZ. Or very very little....to be more precise. Share this post Link to post Share on other sites
nio48 0 Posted July 21, 2009 Well, to answer your question more simpy......."There's no air....up there." ZZ. Or very very little....to be more precise. I am not a meteorologist but I believe that it would be more accurate to say that there is less air pressure up there at 10,000 ft. I found this:- The atmosphere extends above the Earth's surface 100,000 ft, and generally remains consistent, with a 78% nitrogen/21% oxygen mixture to about 70,000 ft. Above that, it becomes more a mixture of helium and other gases. This being the case, and because the highest elevation we find on Earth is about 30,000 ft, we can't really say that oxygen decreases with height. However, what does decrease with height is air pressure. At sea level, the pressure of the atmosphere is 14.7 pounds per square inch (psi). At 18,000 feet the pressure is 7.34 psi. By 34,000 feet, the pressure is reduced to one-half the value at the 18,000 foot level (3.62 psi). It is this reduction in pressure (or in other words, the less dense air) that causes hypoxia, a condition during which the pressure in the blood is not sufficient enough to deliver oxygen to the brain. The barometric pressure at 10,000 ft is ~670 mb. Meteorologists often use the following scale when describing specific altitudes. For instance, they will say, "The freezing level is at 850 mb." 1000 mb ~ 360 feet (110 m) 850 mb ~ 5000 feet (1500 m) 700 mb ~ 10,000 feet (3000 m) 500 mb ~ 18,000 feet (5400 m) 250 mb ~ 34,000 feet (10,200 m) E & OE best nio Share this post Link to post Share on other sites
zoomzoom 2 Posted July 21, 2009 Now THATS much more precise! :yes: ZZ. Share this post Link to post Share on other sites