Leaderboard

Not another Sea Harrier FA2 I hear you say.........well...yes. Original Mirage Factory max file extensively rebuilt by me, too many modifications to mention, same goes for the pit. Backup any other versions you may have as unlike a lot of mods posted on here nowadays I'm not telling you to dump other folks hard work because mine is better.....you decide for yourselves (rant mode off). You WILL need Thrust Vectoring set up in your controls to fly this thing. Please read the ReadME......without it this thing would not of got released.. Mirage Factory product. Have fun.

F-4E RAAF pack Includet: - F-4E - F-4E with MIDAS4 gun muzzle fairing - weapons Hangar and Loading screens are in 1920 x 1080 , optional 1024 x 768 Hangar and Loading screens are includet in a separate folder Installation: - Drop all files into your mod folder the way they are setup in this pack and overwrite if ask to - If you are unsure about the way how mods are installed, check the knowledge base at CombatAce! Credit - original model by TW , BPAO , Crab_02 - cockpit by TW - new updated model , textures and weapons by ravenclaw_007 have fun , ravenclaw_007

Kuril Islands 1.0 ***************************************************** This terrain is written for SF2. +++++++++++++++++++++++++++++++++++++++++ I. Short description: This terrain covers the Kurils islands, a small group of islands which were conquered by the soviets in September 1945 from Japan. There is also a small part of the japanese island of Hokkaido. This terrain is made for carrier ops in primary. You may fly ground based planes too. There are two small japanese airfields and 3 soviet airfields. The soviets deployed an aray of SAM sites over the islands of Kunashir and Iturup. To run this terrain you need SF2NA and one of these: SF2I or SF2E. ++++++++++++++++++++++++++++++++++++++++++++++++ II. INSTALLATION: Unzip all files into your saved game folder ...ThirdWire\StrikeFighters2NorthAtlantic /terrain folder. Because IcelandNA terrain does not include all neccessary objects to run this terrain properly you need to link it to an other terrains CAT file. From stock the terrain is prepared to link with SF2 Israel If you dont have SF2I you must open the file kurilen.ini with Windows notepad editor. Look for the lines: CatFile=..\IsraelME\IsraelME.cat //CatFile=..\GermanyCE\GermanyCE.cat //CatFile=..\VIETNAMSEA\VietnamSEA.cat //CatFile=..\Desert\Desert.cat Add // in front of CatFile=..\IsraelME\IsraelME.cat to switch ot off. Then remove // at one of the other lines. Which you should remove depends on which SF2 game you still have installed side by side with SF2 North Atlantic. Save it. Thats it. ++++++++++++++++++++++++++++++++++++++++++++++++++ III. Credits. The TOD's, what means the trees and autogenerated houses on the map, are mostly taken from various tilesets made by Stary. The SAM protection walls are taken from Pureblues AirfieldDevKit. They were originaly made by Sundowner. The basic files for the taxiways, parking areas and quais are made by ErikGen. I hope i have not forgotten someone. . ++++++++++++++++++++++++++++++++++++++++++++++++ IV. This Terrain is Freeware. Commercial use is not allowed. +++++++++++++++++++++++++++++++++++++++++++++++++ V. For remarks, comments, bugs, etc please use CombatAce forum or send me a PM. Hope you enjoy it. Michael (Gepard) Made in Germany 18 November 2018

This cockpit will replace Fokker D7 cockpit used until now to make the stock DFW C.V into a flyable plane. I can't find out who first converted the stock DFW into a flyable plane by using the cockpit from the Fokker D7. It seems to have been done several times over the years. I found a mod to convert the DFW C.V into a C.I uploaded by Christian59 in 2007 which used the Fokker cockpit, and it seems to have already been done before. The most recent version I could find was by JacksonM in 2017 and was included with his Hangar Screen pack. I have used parts of the cockpits I made for other German planes to make a completely new cockpit for the DFW C.V which fits the fuselage better and has the correct placement for the gun. The new cockpit features fully functional gauges, throttle, rudder control, and stick. This cockpit should work with the DFW in both FE1 and FE2. NOTE - There is a typo in the stock FM for DFW C.V which causes the Fuselage to disappear in the cockpit view. I have included instructions to correct the typo. If you are using one of the modded FMs, you may need to correct the typo there too, check to be sure. Instructions to fix the Data.ini are included in the download in a separate text file. Installation Instructions for both FE1 and FE2 If you have already have a flyable DFW C.V using the FokkerD7 cockpit, delete the "cockpit" folder if it exists, and delete the DFWC5_cockpit.ini file. Then open my "DFWC5" folder and place all the files - 1 folder and 1 ini file - into your DFWC5 folder. You will also need to change one word in the DFWC5_data.ini. See the file named "ChangeForDFWC5DataIni" If you still have the stock version, Open my "DFWC5" folder and place all the files - 1 folder and 1 ini file - into your DFWC5 folder. You will also have to add the following line to the plane's ini file. CockpitDataFile=DFWC5_cockpit.ini You will also need to change one word in the DFWC5_data.ini. See the file named "ChangeForDFWC5DataIni" NOTE - If the DFWC5_data.ini is not in the folder, you may need to extract it from the ObjectData.cat file using one of the utilities found here at CombatAce.